Middlebury

Difference between revisions of "Axinn SMART Classroom Guide"

m
Line 1: Line 1:
== Axinn 103 ==
+
[[axn103|Axinn 103]]
  
'''Location of Equipment'''
 
  
Axinn 103 is equipped with a projection system that accepts input from your laptop computer, a VCR, a DVD player, and auxiliary video equipment and projects the output onto the screen at the front of the room for display. All equipment is controlled by the Touch Panel system. The relevant equipment is located at:
 
 
Equipment Location
 
 
Touch Panel A small screen on the wall behind the lectern
 
 
Projector Hanging from the ceiling
 
 
Projection screen In wall pocket at the front of the room
 
 
Computer interface cables Emerge from the lectern
 
 
Computer network cable Emerge from the lectern
 
 
Power source for computer Just below the lectern top and in the compartment from which the interface
 
cables emerge
 
 
DVD player In the equipment rack
 
 
VCR In the equipment rack
 
 
Auxiliary equipment adaptors In the equipment rack
 
 
'''Using the Touch Panel'''
 
 
The control system for audio-visual equipment in this room is incorporated in the Touch Panel system.  An overview of your interaction with the Touch Panel system is:
 
1. Touch the Touch Panel screen anywhere to activate it.  Note that you should use a deliberate pressing motion when interacting with the controls rather than a light tap or a hard jab.
 
2. When the Axinn Room 103 screen appears, touch Touch Here To Begin .
 
3. Touch the button for the equipment you want to use.  Control the equipment you want to use with the Touch Panel system, including room lights, projection screen, your laptop computer, DVD player, VCR, and auxiliary computer and video equipment.
 
Note:  From all control screens you can touch Main Menu to return to the main menu.
 
 
 
4. When you are finished:
 
a. Touch Main Menu, then touch System Shutdown to end your session.  The Shutdown Warning displays.
 
b. Touch System Off to end your session or touch Cancel if you’ve started the shutdown process by mistake.
 
Note:  You cannot turn the projection system back on for 3 minutes after shutdown.
 
 
Notes:  It is important that everything is turned off to extend the life of the electronic equipment.
 
You must remove your media from the equipment BEFORE you turn off the system power.
 
 
'''Screen Controls'''
 
 
1. On the main menu touch Screen Control.
 
2. Touch up arrow or down arrow to raise or lower the projection screen.
 
 
'''Room Light Controls'''
 
 
1. On the main menu touch Lights.
 
2. Touch Full, Medium, Low, Video, or All Off  to your preferred adjustment.
 
 
'''Microphone Controls'''
 
 
1. To change microphone volume settings of the lectern microphone touch Mic Level on any of the device control screens.
 
2. Touch up arrow or down arrow to raise or lower the volume.
 
3. Touch Mute to turn off the microphone.
 
 
 
----------------------------------------------------------------------------------------------------------------------------------------
 
 
 
'''Projection from the DVD Player'''
 
 
1. Follow steps 1-3 in the section Using the Touch Panel.
 
2. Touch DVD on the menu.  The DVD Player menu displays.
 
3. Press the Eject button on the DVD player and load the media into the player.
 
4. Press the Eject button on the DVD player again to close it.
 
5. Several buttons on the DVD Controls menu help you control the viewing of your video.
 
• Prev Chap reverses the DVD by one chapter; each touch of the button reverses play by one chapter.
 
• Scan Rev touch to play in reverse.
 
• Play begins play.
 
• Pause pauses the DVD leaving the image on the screen.
 
• One touch of  Stop/Eject stops the DVD and projects a medium blue blank image on the screen. The DVD will restart from the point where you stopped. To cancel the resume feature, touch Stop/Eject again.
 
• Scan Fwd touch to fast forward.
 
• Next Chap fast-forwards the video by chapter; each touch forwards by one chapter.
 
• Close Caption activates the Close Caption feature.
 
6. Sound volume is increased or decreased by touching up arrow or down arrow on the Touch Panel, or touch Mute to eliminate sound.
 
 
 
7. To activate the DVD menu, touch DVD Menu, the menu on the disc will display on the projection screen.
 
a. Touch the directional buttons (up, down, left, or right) to move around the menu.
 
b. Touch Enter to select a highlighted menu item.
 
c. Press Done to return to the DVD menu
 
8. Remove the DVD by touching Stop/Eject twice.
 
9. When you are finished:
 
a. Touch Main Menu, then touch System Shutdown to end your session.  The Shutdown Warning displays.
 
b. Touch System Off to end your session or touch Cancel if you’ve started the shutdown process by mistake.
 
Note:  You cannot turn the projection system back on for 3 minutes after shutdown.
 
Notes:  It is important that everything is turned off to protect the integrity of the security system and extend the life of the electronic equipment.
 
You must remove your media from the equipment BEFORE you turn off the system power.
 
 
 
'''Projection from the VCR'''
 
 
1. Follow steps 1-3 in the section Using the Touch Panel.
 
2. Touch VCR on the menu.  The VHS Deck menu displays.
 
3. Load the video into the VCR; it begins to play automatically, if the cassette’s tab is broken.
 
4. Several buttons on the menu help you control the viewing of your movie.
 
• Fast Rewind reverses the video.
 
• If you want a medium blue blank image projected onto the screen during reverse play, touch Stop, then Fast Rewind .
 
• If you want to scan the video in fast reverse and have it display on the screen, touch Fast Rewind while the video is in Play mode.
 
• Play begins video play.
 
• Pause pauses the video leaving the image on the screen.
 
• Stop stops the video and projects a medium blue blank image on the screen.
 
• Fast Forward performs a fast-forward scan of the video.
 
• If you want a medium blue blank image projected onto the screen during forward scan, touch Stop, then Fast Forward  (you can monitor progress with the time indicator on the VCR).
 
• If you want to scan the video in fast forward and have it display on the screen, touch Fast Forward  while the video is in Play mode.
 
• Close Caption activates the Close Caption feature.
 
 
 
5. Sound volume is increased or decreased by touching up arrow or down arrow on the Touch Panel.  You can also touch Mute to eliminate sound broadcast.
 
6. Remove the video by pressing Eject on the VCR.
 
7. When you are finished:
 
a. Touch Main Menu, then touch System Shutdown to end your session.  The Shutdown Warning displays.
 
b. Touch System Off to end your session or touch Cancel if you’ve started the shutdown process by mistake.
 
Note:  You cannot turn the projection system back on for 3 minutes after shutdown.
 
Notes:  It is important that everything is turned off to extend the life of the electronic equipment.
 
You must remove your media from the equipment BEFORE you turn off the system power.
 
 
 
'''Projection from Auxiliary Equipment'''
 
 
A special set of input receptacles is located in the equipment rack inside the lectern.  Use them to connect other audio/visual sources such as U-Matic, Beta or multi-standard type VCRs such as PAL or SECAM compatibles.  The projectors are compatible with all current video standards.
 
1. Connect your equipment using special audio and video interconnection cables (contact Media Services) to a special set of receptacles located in the lectern.
 
2. Refer to the device manual for set-up and operating instructions.
 
3. Follow steps 1-3 in the section Using the Touch Panel.
 
4. Touch Aux Sources.
 
5. Touch Aux S-video, Aux Video, Rack VGA, or Floor VGA No Audio to select the appropriate auxiliary video source.
 
6. Sound volume is increased or decreased by touching up arrow or down arrow on the Touch Panel.  You can also touch Mute to eliminate sound broadcast.
 
7. When you are finished:
 
a. Touch Main Menu, then touch System Shutdown to end your session.  The Shutdown Warning displays.
 
b. Touch System Off to end your session or touch Cancel if you’ve started the shutdown process by mistake.
 
Note:  You cannot turn the projection system back on for 3 minutes after shutdown.
 
Notes:  It is important that everything is turned off to protect the integrity of the security system and extend the life of the electronic equipment.
 
You must remove your media from the equipment BEFORE you turn off the system power.
 
  
 
== Axinn 104<br>  ==
 
== Axinn 104<br>  ==

Revision as of 19:32, 29 October 2013

Axinn 103


Axinn 104

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Axinn 109

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Axinn 219

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Axinn 220

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Axinn 229

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Axinn 232

More information for this classroom will be coming soon.

For troubleshooting tips go to go/troubleshoot.


Powered by MediaWiki