Middlebury

Difference between revisions of "Routers and Wireless Access Points"

(Added categories)
m
 
(13 intermediate revisions by 3 users not shown)
Line 1: Line 1:
==Routers must come to US==
+
<br>
  
Routers and Airport wireless devices need to be configured '''by us''' for two main reasons:
+
== Personal Routers (of any type): ==
  
*We need to register them manually.
+
Personal routers of any type are prohibited on the Middlebury Campus network.
*DHCP must be turned off so that the router is not assigning private IP addresses to its computers. The "router" part of the router or Airport must be disabled so that it functions only as a wireless access point, this is also called "Bridge" mode.
 
*What we want to avoid is a situation where the router acts as a DHCP server, taking the place of Middlebury's DHCP server. Computers at Middlebury College need to have addresses assigned by the Middlebury College DHCP server for a number of reasons.
 
  
==Details==
+
<br>
  
Wireless Access Point Configuration Guidelines
+
According to the [http://www.middlebury.edu/about/handbook/lis/network_policies handbook&nbsp;]&nbsp;:
  
#WAP delivered to helpdesk (w/ documentation, by owner, do not check devices in, configure them with the owner –see below)
+
Home networking devices, such as DSL or cable-modem devices, home routers, wireless routers and wireless access points, etc., can cause serious disruption of campus network services. The default, "out of the box" configurations of many of these are such that, if connected directly into the campus network, they can disable network access for an entire subnet. No such device may be connected to the campus network without prior consultation and approval of LIS network management staff. Discovery of unauthorized devices may result in immediate disconnection of network service. If a device is found to be disrupting network services, it will immediately be disconnected from the network while LIS staff members attempt to contact the owner.
##(note that Apple AirPort WAPs should be configure with Apple's AirPort Setup Assistant or AirPort Utility - these can be installed with the CD that came with the WAP or by using the Helpdesk iMac which has them in the /Applications/Utilities folder)
 
#Connect to WAP w/ HD computer (via Ethernet cable – use switch ports, NOT internet, uplink or WAN port)
 
#Browse to the WAP – http://ip_address_of_wap (ipconfig from computer will provide default gateway = WAP address )
 
##Logging in will depend on make/model of the device, use the documentation or try a Google search to find default username/password
 
##The IP address of the WAP is usually (but not always) 192.168.1.1
 
#Configure WAP:
 
##Disable DHCP (note that once this happens you will need to RESET the AP to configure it again)
 
##Set SSID to username
 
##Enable WEP or WPA (user sets password – can be shared)
 
##Admin Password for WAP (user sets password – not to be shared)
 
#Test WAP (connect WAP to network jack, connect a computer wirelessly, confirm 140.233.x.x IP address for computer)
 
#Tape Label on WAP (SSID=username; IP Address of WAP – from step 3; and tape over WAN/uplink port)
 
  
If for some reason you need to reset the AP, look for a small button labeled "RESET". Note that resetting the AP will usually undo all the steps that were done before, including erasing any passwords that were set. Consult Google or the AP's documentation for more details on how to reset an AP.
+
<br>
  
 +
Related pages:
  
==Setup: Airport==
+
*[http://mediawiki.middlebury.edu/wiki/LIS/Wireless_Troubleshooting Wireless Troubleshooting] <br>
  
#Turn on MacBook. Plug airport in via Eth downlink to computer, then plug in power but do NOT plug in WAN uplink.
+
[[Category:Routers]]
#Check network settings to ensure that computer is getting connectivity via Eth port, but the address should be 192... or 169..., not 140.233.... That means that the Airport router is working and isn't connected to the wider internet.
+
[[Category:Mac]]
#Open utilities -&gt; Airport Setup Utility (CD in Helpdesk if not auto installed). ASU should detect your Airport after some searching.
+
[[Category:Helpdesk Documentation]]
#Enter "Manual Setup" and configure the Airport accordingly: register according to MAC address, DHCP should be off...
+
[[Category:Public Search]]
 
 
#Unplug power from the Airport, plug in Eth from WAN network, plug back in. If settings are correct, when the airport reinitializes, it should get a 140.233 address and the computer connected to it should also get a 140.233 address (while connected by wire).
 
 
 
== See also ==
 
* [[Wireless]]
 

Latest revision as of 09:46, 23 August 2013


Personal Routers (of any type):

Personal routers of any type are prohibited on the Middlebury Campus network.


According to the handbook  :

Home networking devices, such as DSL or cable-modem devices, home routers, wireless routers and wireless access points, etc., can cause serious disruption of campus network services. The default, "out of the box" configurations of many of these are such that, if connected directly into the campus network, they can disable network access for an entire subnet. No such device may be connected to the campus network without prior consultation and approval of LIS network management staff. Discovery of unauthorized devices may result in immediate disconnection of network service. If a device is found to be disrupting network services, it will immediately be disconnected from the network while LIS staff members attempt to contact the owner.


Related pages:

Powered by MediaWiki